Ghost Immobiliser Fitting
Secure your vehicle from theft of keys hacking, cloning and theft by using the world's first aftermarket immobiliser for CAN. The Ghost app and GPS tracking can be connected to the immobiliser to give you alerts when your car is stolen or tampered with.
Installing a Ghost immobiliser is relatively straightforward for a skilled technician. It is essential to have the appropriate equipment and heat shrink tubing.
Getting Started
Ghost immobilisers are a great alternative to physical theft devices such as wheel locks and car alarms. They safeguard your vehicle without using LED indicators or key fobs. They are directly connected to the ECU CAN data network and can only be activated after entering a PIN. This provides a higher level of security against key hacking, ECU swapping and cloning.
In the end, installing a ghost immobiliser Birmingham must be completed with extreme speed and accuracy. It's like walking through a minefield. One misstep could cause serious damage to your vehicle's circuits. It is important to understand the procedure for installing and prepare your vehicle in a timely manner.
It is necessary to remove interior panels from the vehicle to make space for the immobiliser. Once you've located the perfect location to hide it put it in place with cable ties to keep it from being removed or altered. Then, clean up the wiring by tying loose wires and using insulation tape or heat shrink tubing to cover exposed connections. This will reduce the risk of a short circuit that is not intended to happen and improve the appearance and reducing the chances of theft.
Finally, identify a source of constant 12V power as well as an earthing point for the ghost immobiliser. Once you have located them, test the power cables with a multimeter. Then, connect the CAN H and L wires from the immobiliser to the identified power source and grounding point.
It is crucial to ensure that all connections are checked and examine the immobiliser to check for indications of corrosion. The process of entering a PIN and launching the car is a great way to test the system. This should be an integral part of your routine, as it will help to spot any intermittent issues early on. Regular testing also helps to prolong the life of the device and ensure that it is operating at peak performance.
Preparing your vehicle
Installing a Ghost immobiliser requires the right skills and knowledge. A wiring diagram of the vehicle is essential for locating the correct wires and establishing precise connections. A multimeter is a great tool to check the electrical value and ensure safety. Cable ties and insulation tape can be used to protect connections from being tampered with and to ensure they are secured. Additionally, a user's guide will provide specific directions tailored to the Ghost Immobiliser model you have.
Once installed the ghost immobiliser will prevent unauthorised engine start by requiring the driver to enter a unique PIN sequence using buttons on the steering wheel or centre console. This can be done manually or remotely through an app for mobile phones, and the code is able to be altered by the owner of the vehicle at anytime. The device is also quiet and unnoticeable by thieves since it doesn't emit radio frequencies.
A ghost immobiliser is connected to the CAN bus of the vehicle, a network which communicates with the electronic control units (ECUs) of the vehicle. It intercepts signals from the ECUs and blocks the engine from starting when it detects a false signal. The system is tamper-proof and weatherproof, but it does not have key fobs or LED indicators to attract the attention of thieves.
It can be positioned behind or in a less noticeable area to ensure that it isn't easily spotted by thieves and does not interfere with vehicle performance. It can be placed in a small container, so it is less likely to be observed by fraudulent salespeople when they test drive.
Its discrete operation and integration with the vehicle's CAN bus network make it an effective deterrent against the latest methods of car theft, like key cloning and signal relay attacks. Combining the system with other security measures will create a formidable barrier to frustrate even the most persistent of thieves. More and more insurance companies suggest or require ghost immobilisers, as they can lower the cost of insurance.
Making the Connections
Ghost immobilisers are quiet, unlike traditional security systems, which can be heard by thieves. They prevent thieves from knowing that your vehicle is on. They also block high-tech methods used to steal vehicles, for instance, OBD port hacking. They can also be installed without leaving permanent marks on your car making them a good option for those planning to sell their car in the near future.
The Autowatch Ghost 2 is a immobiliser CANbus that is among the most reliable and advanced solutions to stop car theft. It uses the CAN data network to shut down your engine and generates a PIN code that only you know, meaning it's difficult for criminals to detect. It can be used in various vehicles and is compatible with a variety of features already in place, such as car alarms, GPS trackers, steering wheel locks, and door lock bypass systems.
If you opt to use a Ghost immobiliser for your vehicle, be sure to refer to the wiring diagram to identify the wires that connect. Verify the location of these wires to ensure that they are in the correct location and mark them with tape or labels to help you keep the track of them. You will also have to locate a consistent power source (12V) for the system and a grounding. Once you have the necessary components, you can begin making the connections to complete the installation.
The ghost immobiliser won't allow your vehicle to start until you enter a pin code through the buttons of the dashboard or steering wheel. This will stop ECU hacking, key cloning, and other techniques of theft from vehicles. It can also be used with other Thatcham approved security devices such as alarms and tyre clips to give your car an even higher level of protection.
As the UK automotive aftermarket industry continues to grow, so do the options for securing your vehicle. With so many options for thieves to gain access and take your car, it's vital to do all you can to prevent it from being stolen. what is ghost immobiliser 's why ghost immobilisers are very popular among responsible car owners.
Testing the System
The Ghost Immobiliser communicates with the vehicle's ECU using an CAN network. This stops the engine from starting until the PIN code has been entered. This makes it very difficult for thieves to steal your key fob to start your vehicle, and even more difficult to disable the system by hacking its electronic.
Ghost Immobilisers can also be used together with GPS tracking devices that can assist you in tracking your vehicle's location and identify it if it's stolen. This feature is not an option that is commonly used in security products that are available from the market however it's an excellent option to increase your security and get peace of mind knowing your vehicle is always protected.
The Ghost-II immobiliser offers not only an enhanced security, but also a pleasant experience for the user, by eliminating the need to use additional key fobs or devices. It has an easy and simple PIN code entry system that is seamlessly integrated into your daily routine. It also has convenience features and deactivation modes that allow you to temporarily disable the immobiliser to valet park or service your vehicle.
Before you begin the installation process, you should familiarize yourself with the vehicle's wiring and prepare the necessary tools. A basic set of hand tools will provide you with the flexibility to make precise connections and a multimeter is a great tool to verify electrical values. Insulation tape and heat-shrink tubing are vital to shield connections from short circuits. Cable ties can also be used to secure wiring. It is also essential to work in a place that is well-lit, and wear protective gear when working with electrical tools and components.
After you've completed the installation, you must test the Ghost immobiliser to make sure that it's working as intended. Try to start the car without entering the PIN. If this fails, you'll need to test the system again and conduct a thorough examination of the connections.
In contrast to other security systems that are available, unlike other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is more effective than traditional physical deterrents such as wheel clamps or steering locks. It is TASSA-approved and endorsed by some insurance companies. This is a cost-effective investment that provides you with the peace of heart you deserve.